Looking in ~ this, you see what is essential to access the Tensioner pulley. Then gain the tools required for this job.

You are watching: 2004 chrysler pacifica serpentine belt replacement

13mm socket serpentine belt tool(can rent from components store)

pry bar 15 mm six-point socket functions best

Phillips head screwdriver

3/8 drive ratchet

And a an excellent pair of wheel chocks or 2 pieces of wood and also It’s a good thought to have actually these in ar while functioning on your auto any means you wouldn’t want your car to run away from friend while her under the hood.


*

A pair of timber blocks would work-related as well. Yet I make these bad boys. Remember safety and security first.


Lucky because that me this car was missing its plastic shields underneath the car. Yet with this car, i didn’t need to go under that to usage my serpentine belt tool. It’s easier from up top anyway, even if this auto had the consist of on it. You require to have actually a flashlight to heat it increase or check out the feet or square notch in the wheel arm.

So ago to the project, you an initial remove the air filter box v a torq screwdriver, then a 5/16 socket for the water tap clamps at the inlet, over there is a clip in through the fender. BE mindful here, utilizing a level tip screwdriver and also patience! girlfriend may need to push the height of the box towards the left side or towards the driver next to acquire this bugger out!!! Sorry ns didn’t obtain THAT picture. Remove the bottom section with one 8 millimeter, 1/4 inch drive socket on one extension, over there is only one.


*

Best usage a to remove this one instead of a screwdriver.


*
*

One of these bolts is just that. A bolt. The other bolt is a guide. Now the fun begins getting to the pulley. Prior to you eliminate the belt, you have to check and see if your car has a sticker because that the belt routing diagram that would generally be ~ above the radiator covering or the underside the the hood indigenous the manufacturer.


*

Belt Diagram prior to tackling this job be sure you have actually taken a photo of the belt routing or attracted a snapshot of it on a item of paper. I promise the will save you a large headache Later.


If girlfriend can’t discover it you must take images or attract a diagram before removing the belt therefore you have a overview to reference. Now, for the removed of the belt tensioner pulley. The bolt size is 15mm on my 3/8 journey ratchet. However only to rest it. I supplied a shallow socket because I was short on an are here! bland front-wheel-drive cars! LOL! ns finished v an opened ended 15 mm wrench, then finger it from there. It’s a tight room holding the pulley tight versus the motor to gain the bolt out, what a pain! Oh, by the way, we additionally replaced our belt here. That was acquiring pretty smooth NOW! Okay, the Tensioner pulley is out! currently in this vehicle remember the goes on backward. Girlfriend will check out a tiny knob ~ above one next that’s the back. This goes versus the engine. As an alignment knob only.


*

Remember to compare her old part to your brand-new part.


*

pay close attention to the knob on the new part and your old part this knob goes into the engine my bolt is in wrong. Just for an example to not do.


Then as soon as you have the wheel mounting bolt began you better start the belt behind it and also watch the remainder of the bland belt, the will relocate like a slippery line on you!!!! If you’re not replacing your belt, just have actually a pry bar or lengthy screwdriver hold it for you uneven you already have the Tensioner.


*

This is the correct method to download this tensioner.


Anyway earlier to the reinstall, feeding the belt under the pulley, and try to save the stress and anxiety at the exact same time till you’re all set to use the serpentine belt tool one last time. Yay! The component is finished!


*

Re-installing our tensioner and also a brand-new belt. Currently looking bottom our bolt isn’t all the means in and tighten down we want to acquire our belt in an initial while whatever is still loosened and we had plenty that wiggle room because that our belt routing.

See more: Nancy Drew Legend Of The Crystal Skull Hints, Nancy Drew: Legend Of The Crystal Skull


Checking every little thing one last time before starting the automobile to be certain it’s really finished and also no extra bolts or nuts other than for screws for the airbox then reinstall the box after everything checks the end fine. YAY! We are finished! victory Cruise.