I had my wait filter changed at Wal-Mart and also while he had the filter the end he take it the waiting hose and blew the dust and also dirt off, and also right right into the north hole. It would hardly run and has acquired better, I put cleaner in the gas and that has helped, but I'm thinking now I may have to adjust the fuel filter, deserve to you phone call me wherein it's located?


You are watching: 2008 nissan altima fuel filter location

*

Hello, Yes the fuel filter is situated in the fuel tank attached come the fuel pump, this filter is typically not serviceable. More recent cars perform no have fuel filters like older dare do. Just a fuel strainer in the tank.This overview should assist with diagrams below to show you on your car.https://www.snucongo.org/articles/how-to-change-a-fuel-filterCheck the end the diagrams (Below). Please let us understand if you require anything rather to get the difficulty fixed.
*

*

vehicle keeps stalling, jerks, and spits and sputters; specifically after I placed gas in the car it will do it a lot.
*



See more: Walt Whitman'S " When Lilacs Last In The Dooryard Bloom D Symbols

The fuel filter is located in the fuel tank. That is taken into consideration a lifetime part that never demands service. To access it, the fuel pump assembly needs removed native the tank. Below are the directions for replacement. Every attached images correlate v the directions. Inspect out the diagrams (Below). Removal and Installation For every Models except PZEVNOTE: The Fuel Filter because that this auto is a "Maintenance complimentary Item", and also does no require program service. 1. Unscrew the fuel filler cap to relax the press inside the fuel tank. 2. Release the fuel pressure from the fuel lines. Describe "FUEL pressure RELEASE". 3. Disconnect the battery an unfavorable terminal. 4. Eliminate the behind seat bottom. 5. Turn the 4 retainers 90 levels in a clockwise direction and remove the fuel pump inspection hole cover.6. Disconnect the fuel level sensor, fuel filter, and also fuel pump assembly electrical connector, EVAP hose quick connector, and also the fuel feeding hose fast connector from the fuel level sensor unit, fuel filter, and also fuel pump assembly. Eliminate the fast connector as follows: - host the political parties of the connector, press in tabs and pull the end the tube. - If the connector and the tube are stuck together, push and also pull numerous times till they begin to move. Then disconnect them by pulling. CAUTION: - The tube deserve to be removed as soon as the tabs are fully depressed. Carry out not twisted it more than necessary. - carry out not use any tools to eliminate the quick connector. - store the resin tube away from heat. Be especially mindful when welding close to the tube. - protect against acid liquid such as battery electrolyte, etc. From obtaining on the resin tube. - do not bend or twisted the tube throughout installation and also removal. - Only when the pipe is replaced, eliminate the remaining retainer on the tube or fuel level sensor, fuel filter, and also fuel pump assembly. - as soon as the tube or fuel level sensor, fuel filter, and also fuel pump assembly is replaced, likewise replace the retainer through a new one (green fancy retainer). - To store the connecting part clean and to prevent damage and foreign materials, covering them completely with plastic bags or other similar.7. Eliminate the lock ring using a socket drive handle and Tool together shown. Tool number : KV991J0090 (J-46214) CAUTION: - Discard the lock ring, carry out not reuse the lock ring. - Discard the ring seal, execute not reuse the ring seal. 8. Remove the fuel level sensor, fuel filter, and fuel pump assembly. CAUTION: - perform not bend the to rise arm throughout removal. - Discard the ring seal, execute not reuse the ring seal.INSPECTION after REMOVALInspect the fuel level sensor, fuel filter, and also fuel pump for any kind of defects and also foreign materials. Replace as necessary.INSTALLATIONInstallation is in the turning back order of removal. Install the fuel level sensor, fuel filter, and fuel pump assembly through the fuel feed hose encountering the former of the car as shown. Usage a new ring seal. - connect the fast connector as follows: - examine the connection for damages or any type of foreign materials. - Align the connector with the tube, climate insert the connector straight into the tube till a click is heard.After the tube is connected, make certain the link is secure by performing the adhering to checks: - pull the tube and the connector come make certain they room securely connected. Visually confirm that the 2 retainer tabs are connected to the quick connector.Check out the diagrams (Below). Please let us recognize if you require anything rather to obtain the trouble fixed.