Honda Civic business Manual / Powertrain / Transmission/Transaxle / automatically / A/T transition Cable Removal and Installation (A/T)

214101

*

1. Center Console panel Assembly (Except '12M M/T)

1.

You are watching: Honda civic automatic shift cable removal

Detach the clips (A).

*

2.

Remove the facility console panel (A).

3.

For part models: Disconnect the connector(s) (B).

2. Cup Holder panel Assembly

1.

Remove the cup holder dashboard assembly (A).

3. Center Console Assembly

*

1.

Remove the bolts (A).

2.

Disconnect the connector (B).

*

3.

Remove the console box mat (A).

4.

Remove the bolts (B).

5.

Disconnect the connector (A).

*

6.

Remove the facility console (A), in the numbered sequence shown.

4. Rear Heater share Duct

1.

Remove the behind heater share duct (A).

5. Shift Cable - Disconnection bar Side

Type A shift lever

*

Type B transition lever

*

1.

Shift the change lever come R.

2.

Insert a 6.0 mm (0.236 in) pin (A) right into the placing holes (B).

NOTE: Use just a 6.0 mm (0.236 in) pin through no burrs.

3.

Remove the nut (C) securing the change cable finish (D).

*

4.

Unlock the retainer lock (A).

*

5.

Rotate the socket holder retainer (A) counterclockwise (B) till it stops, and push the retainer lock (C) right into the socket holder retainer to lock the retainer.

Type A shift lever

*

Type B shift lever

*

6.

Slide the socket holder (A) away from the bracket as displayed to eliminate the transition cable (B) native the shift cable clip (C).

NOTE: perform not eliminate the shift cable through pulling the change cable overview (D).

6. Raise The auto On The Lift

1.

Raise the automobile on the lift.

7. Shift Cable Cover

*

1.

Remove the change cable covering (A).

8. Shift Cable - Disconnection A/T Side

*

1.

Pry under the lock tab that the lock washer (A).

2.

Remove the lock bolt (B) and the lock washer.

3.

Separate the shift cable (C) from the selector manage shaft (D).

NOTE: perform not bend the change cable excessively.

4.

Remove the shift cable holder (E).

9. Shift Cable

*

1.

Remove the heat shield (A).

*

2.

Remove the transition cable bracket (A).

3.

Remove the shift cable grommet (B), and pull the end the shift cable (C).

NOTE: carry out not bend the change cable excessively.

*

1. Shift Cable

1.

Insert the shift cable (A) with the grommet feet (B), and also install the transition cable grommet (C) in that hole.

NOTE: execute not bending the change cable excessively.

*

2.

Install the change cable clip (D).

*

3.

Install the warmth shield (A).

2. Shift Cable, A/T side - Reconnection

*
......u....(nas

1.

Install the transition cable holder (A).

2.

Install the manage lever (B) end the selector manage shaft (C).

NOTE: perform not bend the shift cable excessively.

3.

Install the lock bolt (D) making use of a new lock washer (E).

4.

Pry up the lock tab (F) of the lock washer against the bolt head.

3. Shift Cable Cover

*
mm:12

1.

Install the change cable cover (A).

4. Shift Cable - Adjustment

*

1.

Push the shift cable (A) until it stops, then relax it. Traction the shift cable earlier one step so that the shift position is in R.

NOTE: do not organize the transition cable guide (B) to change the change cable.

*

2.

Turn the ignition move to ~ above (II).

3.

Check the the R position indicator comes on.

Type A change lever

*

Type B transition lever

*

4.

Align the shift cable slot (A) between the socket holder (B) and also the socket holder retainer (C) with the opened (D) in the transition cable clip (E), then slide the holder right into the parentheses while installation the transition cable end (F) end the mounting stud (G) by aligning that is square hole (H) with the square fitting (I) in ~ the bottom that the stud.

NOTE:

Do no install the transition cable by hold the change cable overview (J).

When the socket holder is set up in the change cable bracket, the retainer lock is unhinged and releases the holder retainer lock, then the holder retainer return under spring force to secure the transition cable.

*

5.

Push the retainer lock (A) totally to lock the socket holder retainer (B), and also make certain that the retainer lock fits into the hinged-joint (C). If the retainer lock does not fit through the leaf of the hinged-joint, turn the holder retainer counterclockwise while advertise the retainer lock until it locks.

*

6.

Make sure that the transition cable end (A) is properly set up on the mounting stud (B).

If the transition cable finish is the end of place with the mounting stud, eliminate the shift cable native the shift cable bracket, then reinstall the cable end over the mounting stud before reinstalling the change cable to the change cable bracket. Carry out not install the transition cable finish on the mounting stud through the transition cable download on the transition cable bracket.

If the change cable finish does not ride in ~ the bottom the the mounting stud, turn the stud to align the square fitting with the hole.

Type A change lever

*
i.z5mm1:m-m(z.115

Type B change lever

*

7.

Install the shift cable end nut (A).

8.

Remove the 6.0 mm (0.236 in) pen (B) that was set up to host the change lever.

9.

Turn the ignition switch to top top (II).

10.

Move the transition lever to each position, and also check that the A/T equipment position indicator complies with the transmission range switch.

11.

Shift the shift lever to P.

12.

Check that the change lock functions properly.

13.

See more: Where To Buy Palo Azul Tea, Greenside Palo Azul Herbal Tea

Push the change lock release, and check that the transition lever releases. Likewise check that the transition lever locks as soon as it is shifted ago to P.